|
Firmware Version 2.02 RC for UFS 910si (20210105) and UFS 910sw (20210089)
The firmware-Version V2.02 RC is a pre-release software in which the following faults have been solved:
- Timeshift -problem on reaching the 4GB-limit
- Timeshift - TS stops too early. If the recording end is reached then the TS stops, even though programme replay has not finished
- Timeshift - after Timeshift is stopped (beforehand REC and EXIT), then the receiver could not be switched off using the standby-key
- BBC HD / ARTE HD DVB Sub
- BBC 1 London TXT problem
- VFD Icons integrated, except Dolby Digital
- after setting the PIP/HDMI resolution the receiver couldn’t be operated, except after EXIT/MENU-key
- SI-updating over night starts even when a recording session is running
- High tone on Scart output in setting "Decoded PCM" -> to stop this one must set to "SPDIF" and then re-start the receiver
Note: this functions only when no HDMI cable is connected in parallel to a Scart cable
- Common Interface -> CAM support
Note:
- After updating the receiver one must carry out a factory setting in the "menu -> Service Menu"
- If the software version 2.00 is already installed, then we recommend updating using a USB stick.
- During the Update process one must disconnect any connected external USB hard disk
- During replaying a recording "Error same pos" can be displayed. This is no fault, but rather an internal test display, which will be removed in the final software release.
Should any provable faults be noted, then please report these over our Kontaktformular.
Provable reported faults will be solved in later software releases.
Tested USB hard disks
| Older Firmware Versions: |
ufs910_fw1.06.zip, Version 1.06, 08/2008
The following improvements and new features are available with software Version 1.06:
Improvements:
- HDMI functionality
- Intermittent picture breakdown on ORF HD
- Teletext subttles
- HDMI video format when replayed
- Scanning of high symbol rate transponders
- Starting to record during a replay
- Teletext symbol in the information banner
New functions:
- Russian language/cyrillic script now settable
- Setting up of network parameter (IP address, sub-network mask, etc.)
Attention:
The simultaneous downloading of programme lists and software over satellite is only possible when the receiver has already been loaded
with the firmware version 1.05. Please check that the firmware version 1.05 has beforehand been loaded if this function is required
otherwise the download will not be carried out correctly.
To load the firmware using a USB stick please do as follows:
Unpack the WinZip file ufs910_fw1.06.zip and update as described in "Guide for updating using a USB stick"
|
ufs910_fw1.05.zip, Version 1.05, 04/2008
Improvements
- Automatic mode for 576i, 720p
- Speech synchronity
- Hard disk/Partition selection in Timeshift
- Software download: Channel list and Software can again be loaded and installed at the same time
- Search process
- Tele-text
- Format switching for 16:9 programmes in Timeshift/Play over Scart
- Dolby Digital problem in recordings solved
New functions
- Channel for time updating now settable
- File system check possible using the Service menu
|
ufs910_fw1.04.zip, Version 1.04, 12/2007
Improvements
- Solving of several errors and stability improvement
- Improved HDMI compatibility
- Improved SI aquisition
- USB recording function now integrated
- Improved internal Tele-text
- Remote control problem solved. Remote control code now settable in the menu
|
ufs910_fw1.03.zip, Version 1.03, 06/2007
Improvements
- Stability improvement
- HotBird search improved
- RGB active after the receiver has been switched off
- Problem solved with zoomed video - i.e. if the receiver was operated via the Scart/Cinch and if a 4:3 transmission was zoomed, then after opening/closing the menu or the channel list only the small viewing window was viewable (the rest of the screen stayed blacked out)
- High frequency whistle on some channels is now stopped
NOTE:
If the receiver was not operated over HDMI, but rather over DVI or Scart/Cinch, then in the menu "Settings/ TV, Video and Audio" the menu section "Audio format over HDMI" must be set to S/PDIF. Then must start the receiver new.
- Remote controller reaction has been improved
- Functionality of the option menu has been improved
|
ufs910_fw1.02.zip, Version 1.02, 05/2006
Improvements
- Solving of various errors and stability improvment
- Option menu implemented for choice of Multi-feed programmes
- Dolby Digital over HDMI implemented
- HDMI Zoom functionality for 4:3 transmissions --> the following zoom modes are available:
- normal (Pillar Box)
- stretched (full screen)
- zoomed (Pan&Scan)
Choice over the menu "Settings/TV, Video, Audio" or using the PIP key in standard TV mode
- Extension of the display functions and title of running programme in news bar
- Single cable command set implemented
|
KATHREIN-Werke KG Rosenheim
last update 31.08.2010
|